Find a system that fits your vehicle

Accessories

Sort By:
Thumbnail Detail
 1 2 3 
  1. CHWFR - Chrysler 2008+ ignition interface wafer Bypasskit XPARTS
    Wafer ignition switch interface for select 2008+ Chrysler, Dodge & Jeep vehicles.
  2. CHWFR - Chrysler 2008+ ignition interface wafer Bypasskit XPARTS
    Wafer ignition switch interface for select 2008+ Chrysler, Dodge & Jeep vehicles.
  3. RFLCH - RFloop for GEN 1 Chrysler Bypasskit XPARTS
    Preloaded RF immobilizer ring for most chrysler vehicles built prior to 2004.
  4. RFLCH - RFloop for GEN 1 Chrysler Bypasskit XPARTS
    Preloaded RF immobilizer ring for most chrysler vehicles built prior to 2004.
  5. RFLKIA2 - RFloop for KIA Bypasskit XPARTS
    Preloaded RF immobilizer ring for Kia Amanti from 2004 to 2007.
  6. RFLKIA2 - RFloop for KIA Bypasskit XPARTS
    Preloaded RF immobilizer ring for Kia Amanti from 2004 to 2007.
  7. RFLMIT3 - RFloop for Mitsubishi Bypasskit XPARTS
    Preloaded RF immobilizer ring for most Mitsubishi vehicles from 2004 to 2008.
  8. RFLMIT3 - RFloop for Mitsubishi Bypasskit XPARTS
    Preloaded RF immobilizer ring for most Mitsubishi vehicles from 2004 to 2008.
  9. RFLUB - Universal RFLoop Bypasskit XPARTS
    Universal RF immobilizer ring to be used with any pre-programmed transponder pellet
  10. RFLUB - Universal RFLoop Bypasskit XPARTS
    Universal RF immobilizer ring to be used with any pre-programmed transponder pellet
  11. XKYD2D5P - 5 Pack - Y D2D cable (2 datakits into 1 D2D port) XpressKit XPARTS
    5 Pack - Y D2D cable (2 datakits into 1 D2D port)
  12. XKYD2D5P - 5 Pack - Y D2D cable (2 datakits into 1 D2D port) XpressKit XPARTS
    5 Pack - Y D2D cable (2 datakits into 1 D2D port)
  13. DTIMAZDA - Open Circuit Door Trigger Interface XPARTS
    The Door Trigger Interface (DTI) will integrate to vehicles with negative polarity for normally closed trigger door pins. It’s designed to combine the individual door signals and deliver them to the remote starter or alarm system as one input signal.
  14. DTIMAZDA - Open Circuit Door Trigger Interface XPARTS
    The Door Trigger Interface (DTI) will integrate to vehicles with negative polarity for normally closed trigger door pins. It’s designed to combine the individual door signals and deliver them to the remote starter or alarm system as one input signal.
  15. CHTHD1 - CHTHD1
    Nothing is easier or faster, with the CHTHD1 you can now shave hours off your installation of a remote starter. The easy to use T-Harness allows for plug & play installations in any TIP start type Chrysler. Simply plug in the CHTHD1 T-Harness between the key switch and the factory ignition harness, plug in a DBALL on the short end and your done*. It's that easy!! With the help of the config tool available online you can select an RF kit of your choice to enable standalone remote start (RSR). *Installation may require the connection of up to three wires for certain models, see installation guide for specific install type for details.
 1 2 3 
Back to Top